[TheList] Pager
Tariq Alkamil
tariq.alkamil at gmail.com
Thu Sep 17 16:55:06 AEST 2015
Hi Sam,
How does the audio sound outputting straight from your radio? You'll want
to make sure you're getting a nice clean signal - Static or pops will throw
the decoder off.
Personally I like setting my PCs input to 100% and my radios output to
nearly silent, and slowly up it's output volume bit by bit to see what the
results like. You can sometimes have to wait a few minutes to see the
effect - It depends how many pages are being sent over the network.
Best of luck,
Tariq
On Thu, 17 Sep 2015 6:13 pm Nick McEvoy <falcon5nz at hotmail.com> wrote:
> A discriminator tap works well if you can solder. Takes the audio before
> the squelch etc.
>
> Sent from my R83.
>
> DogSecurity - Richard <richard at dogsecurity.co.nz> wrote:
>
> That's partly good, means everythings working right. Now is the hard part
> (hope you have a dedicated radio for this, you won't want to do this every
> time) now you need to adjust the scanner volume and the audio input volume
> on the computer, until you start getting hits. I run 3.12 and it shows
> in the top right hand corner a percentage of hits that are being
> successfully decoded. Naturally you want this 95% or more.
>
> It can be frustrating! MY Uniden 72XLT is dedicated, and set to about
> quarter volume and my input (I use an external USB soundcard for the input
> so I can use my onboard sound for normal usage/skype etc) set to 90% with
> AGC turned off
>
>
>
> On 17/09/2015 5:47 p.m., Sam Sword wrote:
>
> So im now getting a whole heaps of random things on the pdw software but
> nothing readable
>
>
>
>
>
> *From:* TheList [mailto:thelist-bounces at radiowiki.org.nz
> <thelist-bounces at radiowiki.org.nz>] *On Behalf Of *DogSecurity - Richard
> *Sent:* Thursday, 17 September 2015 5:34 PM
> *To:* thelist at radiowiki.org.nz
> *Subject:* Re: [TheList] Pager
>
>
>
> it's a nationwide frequency :) More than just fire use Paging, so you'll
> get all sorts of stuff.
>
> I assume, given your comments, you mainly want to watch for fire turnouts,
> using PDW use filters with what you would like or the address "00099????"
> and you should be good to go, once you get the volume levels of
> scanner/input card working right :)
>
> Cheers,
>
> Richard / Z-master
>
>
>
> On 17/09/2015 5:30 p.m., Sam Sword wrote:
>
> I assume this is Auckland Fire?
>
>
>
> *From:* TheList [mailto:thelist-bounces at radiowiki.org.nz
> <thelist-bounces at radiowiki.org.nz>] *On Behalf Of *
> shiters_r_us at hotmail.com
> *Sent:* Thursday, 17 September 2015 5:19 PM
> *To:* thelist at radiowiki.org.nz
> *Subject:* Re: [TheList] Pager
>
>
>
> 157.95000
>
> Regards
>
> Brendan
>
>
>
>
> On Wed, Sep 16, 2015 at 9:17 PM -0700, "Sam Sword" <ssword at slingshot.co.nz>
> wrote:
>
> Helllo,
>
>
>
> I am after pager freq in the Auckland and Chch areas,
>
>
>
> I am unable to find any, im really after anything that’s out there mainly
> fire though
>
>
>
> Cheers
>
>
>
>
> _______________________________________________
>
> TheList mailing list
>
> TheList at radiowiki.org.nz
>
> http://radiowiki.org.nz/mailman/listinfo/thelist_radiowiki.org.nz
>
>
>
>
> _______________________________________________
> TheList mailing listTheList at radiowiki.org.nzhttp://radiowiki.org.nz/mailman/listinfo/thelist_radiowiki.org.nz
>
>
> _______________________________________________
> TheList mailing list
> TheList at radiowiki.org.nz
> http://radiowiki.org.nz/mailman/listinfo/thelist_radiowiki.org.nz
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://radiowiki.org.nz/pipermail/thelist_radiowiki.org.nz/attachments/20150917/581840df/attachment.html>
More information about the TheList
mailing list